How to Cut Down a Small Tree With a Saw

A small tree is defined to be a species of full-grown tree which usually grows in height not less than 15 feet and a maximum height might reach up to 24 feet with maximum spread of 24 feet endorsed by the botanists. Sometimes we need to fell trees for various reasons.

There are few unique techniques that applied to fell a small tree in a safer way to avoid workplace hazard and inappropriate way of felling. 

The most important aspects include preparing a feeling spot examining all safety aspects, using right saws and right technique to cut down the tree. Creating notch at a right position of the tree is another key aspect to keep in mind.

You must make sure you have enough grip to hold your tree firmly while felling takes place. Eco-friendly aspect has to be taken into account before cutting down your tree to protect environmental safety. 

However, I have designed this article to discuss in detail how to cut down a small tree with a saw to make you familiar with techniques before commencing your tree felling project.      

how to cut down a small tree with a saw

Techniques of Cutting Down Small Tree Using Saws

As I said, a few basic techniques you must adhere to before and during cutting down trees. Post cutting aspects are also vital for safely accomplishing your tree felling project. Always gather all materials that you need to cut down your trees.

Below are the safest and simplest ways you should follow through for cutting down trees. Be trained on creating a notch at the right spot of the tree for safer felling. 

Wear Safety Equipment

For felling trees wear all safety equipment including helmet, eye-protective goggles, boots, and jacket to prevent hazard and injuries at tree felling site.  

Examine Tree Felling Area

Examine carefully around the felling area to ascertain there are no structures, electric wares, by-pass road or other trees which might cause inconvenience for your project tree to fall safely.

Make sure the felling environment is completely safe before cutting down your tree. Also check out vigilantly if there is any debris and clean the felling site to avoid a hazardous environment. 

Determine the Leaning Direction and Stability of the Tree

It’s important to determine where the tree stands out sturdily, if it’s quite stable and healthy etc. as these aspects impact on safer falling of the tree.

Another safety aspect is to consider the tree’s leaning direction. Leaning direction significantly leads the tree to fall down to the certain direction as the tree itself is not able to change its own direction while falling down.  

Ascertain Falling Path

Another important aspect to ascertain is that there is no structure, trees, power lines, or roads around the falling path so that the tree can fall safely without hitting anything around. 

In this step, do some calculation including height of the tree and distance between the base of the tree and falling area. This measurement would prevent all types of hazards during felling of the tree. 

However, you should also create a small notch on the side of the tree to get your tree inclined towards falling direction for falling safely. If your tree is loaded with too many branches, it’s good to cut down them at the beginning to free your tree. 

Determine Exit Way During Falling

Determine exit area so that you can escape to a safe distance while the tree falling takes place. It’s a vital task to prevent accidents and injuries. Never walk over or stand near the tree when your tree starts falling after cutting down. 

Felling Tree With ChainSaw

The first task is to make a notch on the tree at a 70 degree angle considering the felling direction of your tree. Make sure the notch maintains the proper measurement so that your chainsaw will be able to cut on the notch. 

The notch must be 1-2 feet off the ground.  After that, take a chainsaw, hold it tightly with both hands to have a strong grip and cut on the notch exactly at 70 degree angle and fell the tree successfully.   

You can also make a horizontal cut at the base of the notch if you want to keep the bottom of the tree straight. 

You can also make a bore cut by inserting the tip of the saw blade through the tree instead of making a cut from the side of the tree.

To produce the bore cut, position your chainsaw blade 1-2 inches away from the border of the notch and push it thoroughly through the tree. Then keep sawing from the back side of the notch until achieving horizontal cut through the other end of the tree.  

Felling Tree With Hand Saw

For producing a horizontal cut with the hand saw, place the teeth of the handsaw 1-2 feet above the roots of the tree and move it in horizontal motion through the tree. Keep going until one-third of the way is made through. Two-handles saw would be helpful and one assistant to do this.

However, hold the saw with both hands to cut the tree. After the horizontal cut, start hatching above the cut to make a notch. For doing so, hold the hatchet with both hands and run the hatchet in vertical motion into the side of the tree at recommended angle and keep cutting until a defined notch becomes visible. 

After that, cut the tree all through using the saw from the back side of the notch. During falling, stay at a safer distance to avoid injuries. 

Concluding Notes

I hope you are familiar now about the essential aspects of felling trees and quite confident to do it yourself for your project. The key equipment including saws, hammer, hatchet and few other accessories you should gather beforehand for smooth operation of your tree felling project. Employ someone to assist you while accomplishing your project.  

Take care of environmental safety aspects while going through the felling process. Maintain all other safety protocols to avoid workplace hazard and injuries.

Application of proper techniques for tree felling project needs adequate training and practice. Starting with cutting down small trees would make you expert overtime and one day you too might be quite capable of dealing with tall trees. 

I would always expect you to share your comments and feedback which is really helpful for us to optimize our service to make it more pro-client. If you share these articles and our website with your family and friends, it could create a path for us to meet more people in the coming days and bring them under the umbrella of our excellent clients’ services.

Read more:

About Gavin Ford

Hi, I am Gavin Ford. I am a full-time power tools salesperson and a part-time mechanic. I help my friends and neighbors with their tools. Which one to buy, how to buy it, how to use it, methods to fix broken tools, and so on. In I will do the same for the rest of the world. You will get everything you need to know about tools for regular and professional use.

Leave a Comment