How to Patch Screw Holes in Drywall Easily

Drywall makes for a cheap, simple to introduce surface when contrasted with mortar, the old standard wall surface. Be that as it may, one of the disadvantages of drywall development for walls and roofs in private homes is that it tends to be harmed reasonably effectively, with splits, gouges, and openings showing up with just moderate effect.

The most widely recognized reason for openings in drywall is when quick swinging entryways cause the door handle to gouge or punch gaps in the wall.  As anybody with dynamic children knows, forceful recess can pretty effectively ding up drywall surfaces.

Drywall is naturally a fairly brittle, delicate material, and it’s intended to be that way so it very well may be cut and fitted rapidly during establishment. Most wall and roof surfaces are just 1/2 inch thick; drywall isn’t intended to be impenetrable.

But, the way that drywall boards are so natural to join also makes it simple to Patch. Easily joint tape and a modest quantity of drywall compound (referred to in the structure exchanges as mud) is everything necessary to fix most little openings in drywall surfaces. Truth be told, painting the drywall in the wake of Patch it may be more troublesome than the Patch itself.

The techniques portrayed here are for little gaps close to 1 to 2 crawls in breadth. Larger holes require an alternate Patch technique.

how to patch screw holes in drywall

Read more: Top 10 Tools for Cutting Drywall – Tested, Rated & Reviewed

Instruments you will Need Include Patch Screw Holes in Drywall: 

  1. Utility blade 
  2. Self-cement work joint tape 
  3. Four-inch drywall blade 
  4. Drywall compound (“mud”) 
  5. Drywall sanding wipe 
  6. Clean Rag 
  7. Paint 
  8. Paintbrush

For this sort of little Patch, a little tub of the premixed joint compound might be simpler to use than stirring up a clump of the compound from dry powder and water.

Instructions to Patch screw Small Holes in Drywall

  1. Using a utility blade, cut away any stray bits of surface paper or gypsum that may project out from the outside of the divider. You need the outskirts of the harmed territory to be level or recessed internally before you fix the hole. 
  2. Cut off two segments of work joint tape, with the goal that every length of tape will stretch out in any event 2 crawls past each side of the gap.
  1. Apply the work joint tape over the hole in a cross-formed example, one piece over the other. Press the tape down with the goal that it completely clings to the divider surface.
  2. Using a drywall blade, carefully spread the entire area with joint compound, gently squeezing to compel the compound through the work of the tape.
  3. Extend some of the joint mixes beyond the gap, at that point smooth it down with the drywall blade. Now, don’t stress if the work tape is visible.
  4. Allow this first layer of joint compound to dry, at that point daintily sand down any high spots, utilizing a drywall sanding wipe.
  5. Repeat the above procedure in any event two additional occasions, sanding between each dried coat until you have a cover fix up the entire region. Take care not to over and—when you have connected and sanded the last coat, the fiberglass work of the joint tape ought not to be noticeable. An excess of sanding risks uncovering the joint tape.
  6. Wipe away all sanding residue with a clean rag, at that point paint over the patch area with coordinating paint. It, for the most part, takes two layers of paint to sufficiently cover the patch area, as the joint compound will, in general, retain paint.

Related Posts: Top 10 Miter Saw Blade for Hardwood, Trim, and Moulding

Following These Steps is Patch Screw Holes in Drywall

1. Get Some Joint Compound, Spackle, and a Putty Knife.

A little compartment of joint compound, pressurized spackle, and a plastic putty blade will cost in many areas. Snatch these provisions and take them home.

Try to blend the joint compound if there are liquids on the top in the wake of opening the holder.

2. Press the Joint Compound Into the Hole.

You’ll need to take a modest quantity of compound and press it directly into the hole.

Keep doing as such until the whole gap has been filled. Take a little more, make the compound flush with the divider, and after that enable it to dry.

Utilize a wet rag to wipe away any excess compound. Clean your putty blade. Rehash this progression after the compound dries if fundamental.

3.  Sand Down the Patch

If the outside of the patch is harsh, at that point sand it down smooth.

An easy drywall sanding block can do this in almost no time after the compound has dried.

4. Spackle the Repair

You don’t put the surface on your patch site, you will most likely observe the blueprint of the hole caused by the screw.

Match the surface with what is as of now on your divider and splash a slight layer.

Rehash if essential. Enable it to dry medium-term for best results.

5. Paint Over the patch Site

In the event that your dividers aren’t white, you’ll have to paint the patch site.

Matchup paints colors and then spreads the surface. For an extensive patch, you may need to paint the whole room or make another complement wall.


Notwithstanding extensive patching, it generally takes an end of the week to carry out the responsibility appropriately and nobody will ever realize that the wall had been harmed when you’re done.

You Might Also Like:

About Gavin Ford

Hi, I am Gavin Ford. I am a full-time power tools salesperson and a part-time mechanic. I help my friends and neighbors with their tools. Which one to buy, how to buy it, how to use it, methods to fix broken tools, and so on. In I will do the same for the rest of the world. You will get everything you need to know about tools for regular and professional use.

Leave a Comment