How to Sharpen a Crosscut Hand Saw in 5 Minutes

Sharpening a saw is an abandoned trait that required an expert first approach for others to finally restart the activity. Now more amateur woodworkers possess the right knowledge and application to sharpen a crosscut saw in the fastest possible time. With more people now preferring to spend time on this instead of money, this article will elaborate on why and how it is easy to undertake such activity within one-twelfth of an hour. 

how to sharpen a crosscut hand saw

Properties of Blades

Understanding the blades of the saw are also fundamental. The blades and teeth are designed of steel that are not rough. This is the reason that regularly sharpening the saw is recommended. If you possess inexpensive ones, it will have rough teeth, which can only be possible through regular sharpening. Before starting to elucidate the process, it is ideal that a right saw file size is needed. The recommended level is 19 centimeters long. 

Wood Requirements 

Now come to the wood. First of all one must learn how to cut wood with the saw. Naturally, it takes just over 20 strokes to cut an inch and a half of wood. If the saw you are choosing passes this criteria , you can consider it acceptable; otherwise, you need to find ways to sharpen it. But that’s not always the case as buying a new saw can be deemed inaccessible and at times unaffordable.

However, a new saw acts as a helper to sharpen the old ones. If you have a new saw it will also enrich your collection . While sharpening, keep two sticks of wood on each side of the saw, making sure that the teeth of the saw are open about a quarter of an inch from the top of the pieces of wood. Then clamp it in the vice as a secondary process.

Chopping Directions

The next step involves having a three-cornered saw file. The files should be as small as less than five inches. The thing that you will adhere to is place the file into the teeth, feel for the angle and start it with a single stroke. With an old saw, comes a lot of problems, the biggest being lack of sharpness.

For sharpening the old saw it must be positioned on the level across the new one, and perpendicular to the long axis of the saw. Therefore place it into a tooth and take a stroke. The strokes have to be small and even, for having the same pressure, length and direction.

After all the installation is done all you need to do is sharpen your old one at each gullet of the new saw. When applying this make sure you are sharpening on one side of each gullet. During the middle of the process you will develop a rhythm.

All About Tooth

Also while continuing to do that you will realize the file is sloping a bit forward. This gives the front of the tooth that extra sharpness that you need for precise cutting with the saw. One thing that you must follow is to never skip a tooth.

What happens if you don’t abide by that? The entire saw has a similar level of teeth. So by brushing your old one with a new each tarnished part of a particular old tooth will be transferred to the subsequent new one. Failing to do that will cause rust to remain in particular teeth. 

Also it is not effective to wipe the entire tooth under one place. The process can be repeatedly painful; however it is anything but complicated. However if you have a poor eyesight you can always use a magnifier to check and get additional light on there.

Sharpening Tips

Once you are accustomed with it your hands will act as autopilot to create the perfect razor-sharp saw. There is no limit on perfection once you let your hands feel it. Once the file slopes towards the toe of the sword. However, there is a recommended level of the blade that can be shown out.

It should not go over half an inch as the bigger the size, the higher the difficulty to make it finer. The best part of such a process is it can make your saw usable for a lifetime. Such a process should be repeated once in every three months.

When completing the process, look back if you have missed any part of the blade that you need to sharpen. Results are a better indicator of the effort, so after completion of the work, use the old saw to check how many strokes are required to reach that level of cut.

Crosscut Hand Saw


FAQs


What Type of Tooth Pattern Should a Crosscut Saw Have?

Crosscut saw this is the punctured spear tooth design. Wet or green wood is difficult to eliminate from the kerf on the grounds that it is tough. In any event, when the fiber is ousted, it obstructs a saw’s cutter teeth.

How Can You Tell If a Crosscut Saw Is a Rip Saw?

With the rip cut, you cut along the grain; while with the cross cut, you cut across the grain. Cutting along the grain is a simple cut; even before you had mechanical saw, you had saws with not many yet huge teeth so you cut as quick and as straight as could really be expected.

Is More Teeth on a Saw Blade Better?

The quantity of teeth on the edge decides the speed, type and finish of the cut. Edges with less teeth cut quicker, yet those with more teeth make a better completion. Necks between the teeth eliminate chips from the work pieces.

Overall Performance

On average the result that occurs is spectacular. Firstly, it takes just over ten strokes to achieve the similar length of cutting. But more than the numbers, it’s the quality of the cut that makes it more appealing. The cuts are now comparatively finer, which occurred from sharpening the saw.

The precision that derives doesn’t make you think that you are using an old saw as the cuts are much neater.  Within the space of two to three minutes, all you need to do a bit more filling of the saw and you will end up getting a new saw with no money and just over five minutes of effort. 

Read more:

About Gavin Ford

Hi, I am Gavin Ford. I am a full-time power tools salesperson and a part-time mechanic. I help my friends and neighbors with their tools. Which one to buy, how to buy it, how to use it, methods to fix broken tools, and so on. In I will do the same for the rest of the world. You will get everything you need to know about tools for regular and professional use.

Leave a Comment